Rigging Accessories

Wire Rope Clips

Forged Wire Rope Clips

  • Each base has a Product Identification Code (PIC) for material traceabilit , the name CROSBY or CG, and a size forged into it.
  • Based on the catalog breaking strength of wire rope, Crosby wire rope clips have an efficiency rating of 80% for 1/8” through 7/8” sizes, and 90% for sizes 1” through 3-1/2”.
  • Entire Clip is Galvanized to resist corrosive and rusting action.
  • Sizes 1/8” through 2-1/2” and 3” have forged bases.
  • All Clips are individually bagged or tagged with proper application instructions and warning information. • Clip sizes up through 1-1/2” have rolled threads.
  • Meets or exceeds all requirements of ASME B30.26 including identification, ductilit , design factor, proof load and temperature requirements. Importantly, these wire rope clips meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
  • Look for the Red-U-Bolt , your assurance of Genuine Crosby Clips.

Malleable Clips

Fist Grips

  • Entire clip is Galvanized to resist corrosive and rusting action.
  • Based on the catalog breaking strength of wire rope, Crosby wire rope clips have an efficiency rating of 80% for 3/16” through 7/8” sizes, and 90% for sizes 1” through 1-1/2”
  • Bolts are an integral part of the saddle. Nuts can be installed in such a way as to enable the operator to swing the wrench in a full arc for fast installation.
  • All sizes have forged steel saddles.
  • All Clips are individually bagged or tagged with proper application instructions and warning information.
  • Meets or exceeds all requirements of ASME B30.26 including identification, ductilit , design factor, proof load and temperature requirements. Importantly, these wire rope clips meet other critical performance requirements including fatigue life, impact proper-ties and material traceability, not addressed by ASME B30.26.
  • Assembled with standard heavy hex nuts.

Piggy Back Wire Rope Clips

Eye Bolts

Machinery Eye Bolts

  • Forged Steel – Quenched & Tempered.
  • Working Load Limits shown are for in-line pull. For angle loading, see
  • page 200.
  • Fatigue rated at 1-1/2 times the Working Load Limit at 20,000 cycles.
  • Recommended for in-line pull.
  • S-279 threaded UNC.
  • M-279 metric threaded.
  • Meets or exceeds all requirements of ASME B30.26 including identification, ductilit, design factor, proof load and temperature requirements. Importantly, these bolts meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.

Shoulder Eye Bolts

  • Forged Steel – Quenched and Tempered.
  • Fatigue rated at 1-1/2 times the Working Load Limit at 20,000 cycles.
  • Working Load Limits shown are for in-line pull. For angle loading, see page 200.
  • Meets or exceeds all requirements of ASME B30.26 including identification, ductilit, design factor, proof load and temperature requirements. Importantly, these bolts meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
  • All Bolts Hot Dip galvanized after threading (UNC).
  • Furnished with standard Hot Dip galvanized, heavy hex nuts.

Forged Eye Bolts

  • Forged Steel – Quenched and Tempered.
  • Fatigue rated at 1-1/2 times the Working Load Limit at 20,000 cycles.
  • All Bolts Hot Dip galvanized after threading (UNC).
  • Furnished with standard Hot Dip galvanized hex nuts.
  • Recommended for in-line pull.
  • Meets or exceeds all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, these bolts meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.

Swivel Hoist Rings

Slide Loc

  • Available in capacities from .5 to 3.2 metric tons.
  • Bail is Forged Alloy Steel – Quenched and Tempered.
  • Bail swivels 360° degrees.
  • Rated at 100% for 90 degree angle.
  • Fatigue rated to 20,000 cycles at 1-1/2 times the Working Load Limit.
  • Meets the Machinery Directive 2006/42/EC guidelines and is marked with CE accordingly.
  • Bolt specification for metric bolt is Grade 10.9 alloy cap screw to SO 898-1.
  • Unique locking mechanism makes the lifting point well suited for quick attachment to load surface. No need for tools.
  • Features QUIC-CHECK® markings on bail to assist in knowing when device is ready for lifting.

Swivel Hoist Rings

  • Top washer has the following features:
  • The Working Load Limit and Recommended Torque value are permanently stamped into each washer.
  • Washer is color coded for easy identification: Red – UNC thread.
  • Individually Proof Tested to 2-1/2 times Working Load Limit.
  • Bolt specification is an Alloy socket head cap screw to ASTM A 574.
  • All threads listed are UNC.
  • BOLT SIZE IDENTIFICATION: The size of the bolt will be stated as in the drawing above. Illustration shows meaning of each dimension given.
  • NOTE: For Special Applications, see page 457.
  • Frame 2 and larger are RFID EQUIPPED.

Heavy Lift Swivel Hoist Ring

  • Forged bail provides the following:
  • Easily readable “Raised Lettering” showing the name Crosby or “CG” and PIC Code for material traceability.
  • Greater durability providing the increased “Toughness” desired in potentially abusive field conditions
  • Larger opening than standard Hoist Ring bail.
  • Top washer is color coded for easy identification (Red for UNC threads and Silver for Metric threads
  • The Working Load Limit and Recommended Torque value are permanently stamped into each washer.
  • Individually Proof Tested to 2-1/2 times Working Load Limit.
  • Available in both UNC Thread and Metric Thread style.
  • BOLT SIZE IDENTIFICATION: The size of the bolt will be stated as in the drawing below. Illustration shows meaning of each dimension given.
  • NOTE: For Special Applications, see page 457.
  • Frame 2 and larger are RFID EQUIPPED.

Pad Eyes

Pad Eyes

  • Forged Steel — Quenched and Tempered.
  • Forged from 1035 Carbon Steel.
  • Excellent welding qualities.
  • Widely used on farm machinery, trucks, steel hulled marine vessels and material handling equipment.
  • Reference American Welding Society specifications for proper welding procedures.

Eye Nuts

Eye Nuts

  • Forged Steel – Quenched and Tempered.
  • Hot Dip galvanized.
  • Tapped with standard UNC class 2 threads after galvanizing.
  • Also available in blank (as forged) item (S-4028) or on request with metric threading ( M-400).
  • Recommended for In-Line pull.
  • Meets or exceeds all requirements of ASME B30.26 including identification, ductilit , design factor, proof load and temperature requirements. Importantly, these products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.

Teacups